Acoustic Display Wireless Signal Detector/Laser Pointing Direction
Indication Detector
Description:
7LP adds a LASER POINTING function, RF bug detector. hidden
transmitters (bugs), wireless spy cameras, cellular phones and
other radio frequency devices. This feature with voice broadcast
and LENS Finder Exposing All Camera Lenses, sensitivity adjustment
and Noise reduction, positioning signal source BAV.B refers to BB
sound, A refers to voice broadcast, V refers to vibration. Also has
a low battery reminder function. If you need a signal detector for
a bug, we recommend this detector for you.
Featured Function:
1. About Acoustic Display
The acoustic display will be affected by the environment noise in
neighbor frequencies. If those noises are stronger than the
acoustic signal strength, the hissing will be louder than the
acoustic display.
The LED indication of Acoustic display is different from B (beep) and V (vibration). The acoustic display will be varying according to the
environment, so please keep tuning the sensitivity tuner to get
better acoustic display.
Under Acoustic display
, it is not able to find (locate) the signal source. Set the
function switch at B (beep) for locating the signal source more
easily.
2. Low Battery Warning
When turn on this device, if the very right LED lights up in red,
it means the built-in rechargeable battery runs down. Please charge
the battery.
3. Assisted Laser Pointing Direction Indication
Additional, VS-7LP has fitted with laser pointer to aid the locating the signal source. When detects signal wave,
the laser pointer will light up to aim the possible direction.
Lower the sensitivity gradually, user can approach and determine
the signal location.
4. Lens Finder Exposing All Camera Lenses
1) Attach the Lens finder on VS-7LP by inserting the plugs into the
2 sockets in the left bottom side of VS-7LP, facing the 8
ultra-bright lights to front side. Note: The Lens finder will not
work if insertion with wrong side. (Please refer to the pictures.)
2) Press down the On / Off switch of Lens finder, the 8
ultra-bright lights start blinking. Point the light beam towards
the suspected area and scan slowly to check the reflection of
illuminated light.
3)Look through the viewfinder, it is more easily to identify the
camera lens. This lens finder also can uncover a hidden wireless
camera even the camera is turned off.
5. About Battery
1) When the very right red LED lights up, it means the battery runs
down. Connect the switching power adaptor to continue the detecting
and to recharge the battery at the same time.
2) When the battery runs down, If the switch is kept at "on", the
battery will be over discharged and will damage the battery. Please
set the on/off Switch at "off" and connect the power adaptor to
charge this unit, it will take about 8 hours to full charge.
3) Battery will be over charged if you keep on charging it without
using that will also damage battery. The producer and seller accept
no liability for the damage caused by the over discharge or charge.
4) If you are not going to use this device for a long time, please
check the battery power once three months. If the battery runs
down, connect the AC adaptor to recharge the built-in rechargeable
battery for eight (8) hours.
6. Sensitivity Adjustment/Interference (Background Noise)Elimination
Turn the Sensitivity Tuner to - (minus) side to decreases the
sensitivity and the detecting distance will be shorter. Turn the
Sensitivity Tuner to + (plus) side to increase the sensitivity and
the detecting distance will be longer.
In the environment with high environment noise, the detecting
threshold will be lower after eliminating the noise. It means the
detecting distance will be shorter.
Specification:
| Power | Ni-MH 7.2V battery pack |
| Battery life | Continuous for 2 days after full charge (standby mode) |
| Detecting frequencies | 50 MHz - 6.0 GHz |
| Dimension | L 14 x W 8 x T 2.5cm |
| Weight | 235g |
| Warning mode 1 | Audible alarm and 10 LEDs |
| Warning mode 2 | Acoustic display via speaker (or through earphone) and 10 LEDs |
| Warning mode 3 | Vibration and 10 LEDs |
* Specification may change without notice.
Notice of Use
1. Unauthorized repair or disassembly of this device will void all
the warranties.
2. Always use manufacturer’s original power adaptor to avoid damage
to the circuit.
3. Avoid water.
4. Do not store this device in an excessively hot place.
5. Avoid knock or drop of this device.
